![]() ![]() Remove the spring and arm from the gimbal (this may require slight Gently pry the head of the spring upwards off of the plastic arm. Spring assembly must now be moved to the left-hand gimbal. Mounted vertically along the inner-left side of the gimbal, the springĪttached at the lower end to a plastic mounting stud. On the right-hand gimbal, notice there is an arm-and-spring type lever.The plastic gimbal may become easily stripped Screw and tighten to a snug fit (making sure the lever maintains properĪlignment over the ribbed area of the gimbal). Lever's hole over the plastic mounting stud on the gimbal, insert the Side, and resting on the ribbed surface of the gimbal. Ratchet end is now pointing upward nearest the switch on the top right So the screw hole is now on the bottom right side of the gimbal, and the Remove the silver metal ratchet lever and screw from the gimbal on the.Rear half, and lay the controller face-down on your workspace. Remove the four screws from the rear of the controller, remove the case.Permanent damage to your InterLink and/or your computer. Make sure your RealFlight InterLink Controller is completelyĭisconnected from your computer.PleaseĬontact RealFlight Support prior to performing this conversion if you have Result of failure to adhere to these instructions properly. Incidental damage to your InterLink controller or personal computer as a Horizon Hobby will not accept responsibility for Please read all instructions carefully before you begin Hemostats (preferred), or needle nose pliers.RealFlight InterLink Controller to Mode 2. The following is instruction to change a Mode 1 This will provide a goodĮlectrical insulator for the solder connections, and a good strain Tubing over the entire solder connection. Apply heat with a heat gun or hair dryer to shrink the Slide all shrink tubes over their respectiveĬonnections.Solder the other end of the ground wire to the outside connection on the "female mono plug receptacle".IMPORTANT: this is the pin located at the 12 o'clock position when looking at the end of the plug itself, as shown in the diagram. Solder one end of the ground wire to pin #2 on the "trainer jack plug".Solder the other end of the signal wire to theĬenter connection on the "female mono plug receptacle".Located at the 2 o'clock position when looking at the end of the Solder one end of the signal wire to pin #4 on.This is simply to apply a small amount of solder onto the bare wire end to prepare it for soldering onto the jacks. "Tin" each end of bare wire with 60/40 rosin-core solder and a hot soldering iron.Make sure to slide the tubes over the wire ends BEFORE making solder connections. Cut enough pieces of shrink tubing to completely cover each solder connection.Twist the bare strands of wire tightly on each wire end. ![]() Strip approximately 1/4 inch of insulation away from each end of each conductor.Cut each conductor to approximately 8 inches in length.Two conductors will be required one conductor for signalĬonnections, one conductor for ground connections. Should be copper, having a high strand count. Adequate wiring to connect both jacks together.The female receptacle has an inner diameter of 3.5mm, a depth of 14mmĪt the tip, and a depth no greater than 8mm for the base. One female mono plug receptacle, compatible with theĭimensions shown for the "RealFlight Interface OutputĬonnector" as shown in the diagram.Style to the plug used on Multiplex trainer cords. One 5-pin round male connector compatible with.For all instructions, reference theĭiagram below. Transmitter interface and the InterLink controller for RealFlight. The following is a description for how to assemble anĪdapter cord to connect a Multiplex transmitter with the parallel port Internet Service: Broadband Internet connection.The connectors on the InterLink Elite Controller interface cord and included adapter are compatible with the trainer ports on most Futaba and all JR, Spektrum, and Tower Hobbies systems.Compatible FM or FM-selectable transmitter (if using the interface mode).Graphics: 3D accelerated video card with 512 MB of dedicated video memory.(A downloadable alternative to the installation disk is not available) Installation: Internal or External DVD Drive.Graphics: 3D accelerated video card with 32 MB of dedicated video memory and full DirectX 9 support (Pixel Shader 2.0).Processor: Intel Pentium 1.0 GHz or equivalent.Operating System: Windows XP, Vista, 7, 8.x, or 10. ![]()
0 Comments
Leave a Reply. |
AuthorWrite something about yourself. No need to be fancy, just an overview. ArchivesCategories |